View BGA2716_280843.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

BGA2716
MMIC wideband amplifier
Rev. 02 -- 24 September 2004 Product data sheet
1. Product profile
1.1 General description
Silicon Monolithic Microwave Integrated Circuit (MMIC) wideband amplifier with internal matching circuit in a 6-pin SOT363 SMD plastic package.
CAUTION This device is sensitive to electrostatic discharge (ESD). Therefore care should be taken during transport and handling.
MSC895
1.2 Features
s s s s s s s Internally matched to 50 Wide frequency range (3.2 GHz at 3 dB bandwidth) Flat 23 dB gain (1 dB up to 2.7 GHz) 9 dBm output power at 1 dB compression point Good linearity for low current (IP3out = 22 dBm) Low second harmonic; -38 dBc at PL = -5 dBm Unconditionally stable (K 1.2).
1.3 Applications
s s s s LNB IF amplifiers Cable systems ISM General purpose.
1.4 Quick reference data
Table 1: Symbol VS IS s21 NF PL(sat) 2 Quick reference data Parameter DC supply voltage supply current insertion power gain noise figure saturated load power f = 1 GHz f = 1 GHz f = 1 GHz Conditions Min Typ 5 15.9 22.9 5.3 11.6 Max 6 Unit V mA dB dB dBm
Philips Semiconductors
BGA2716
MMIC wideband amplifier
2. Pinning information
Table 2: Pin 1 2, 5 3 4 6 Pinning Description VS GND2 RF_OUT GND1 RF_IN
1 2 3
SOT363
Simplified outline
6 5 4
Symbol
1 6 4 2, 5
sym052
3
3. Ordering information
Table 3: Ordering information Package Name BGA2716 Description plastic surface mounted package; 6 leads Version SOT363 Type number
4. Marking
Table 4: BGA2716 Marking Marking code B7Type number
5. Limiting values
Table 5: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol VS IS Ptot Tstg Tj PD Parameter DC supply voltage supply current total power dissipation storage temperature junction temperature maximum drive power Tsp 90 C Conditions RF input AC coupled Min -65 Max 6 30 200 +150 150 -10 Unit V mA mW C C dBm
9397 750 13292
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
2 of 14
Philips Semiconductors
BGA2716
MMIC wideband amplifier
6. Thermal characteristics
Table 6: Symbol Rth(j-sp) Thermal characteristics Parameter thermal resistance from junction to solder point Conditions Ptot = 200 mW; Tsp 90 C Typ 300 Unit K/W
7. Characteristics
Table 7: Characteristics VS = 5 V; IS = 15.9 mA; Tj = 25 C; measured on demo board; unless otherwise specified. Symbol IS s21 2 Parameter supply current insertion power f = 100 MHz gain f = 1 GHz f = 1.8 GHz f = 2.2 GHz f = 2.6 GHz f = 3 GHz s112 s22 2 input return losses output return losses isolation noise figure bandwidth stability factor saturated load power load power f = 1 GHz f = 2.2 GHz f = 1 GHz f = 2.2 GHz f = 1.6 GHz f = 2.2 GHz NF B K PL(sat) PL(1dB) f = 1 GHz f = 2.2 GHz at s212 -3 dB below flat gain at 1 GHz f = 1 GHz f = 2.2 GHz f = 1 GHz f = 2.2 GHz at 1 dB gain compression; f = 1 GHz at 1 dB gain compression; f = 2.2 GHz IM2 second order at PL = -5 dBm; intermodulation f0 = 1 GHz product input, third order intercept point output, third order intercept point f = 1 GHz f = 2.2 GHz f = 1 GHz f = 2.2 GHz Conditions Min 13 21 22 22 21 20 19 15 10 10 9 30 33 3 10 6 8 5 36 Typ 15.9 22.1 22.9 23.1 22.8 22.1 20.8 17 12 12 11 31 35 5.3 5.5 3.2 1.4 1.9 11.6 7.5 8.9 6.1 38 Max 21 23 24 25 24 24 22 5.4 5.6 dBm dBm dBm dBm dBc Unit mA dB dB dB dB dB dB dB dB dB dB dB dB dB dB GHz
s122
IP3in
-2 -8 21 15
-0.7 -6.9 22.2 15.9
-
dBm dBm dBm dBm
IP3out
9397 750 13292
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
3 of 14
Philips Semiconductors
BGA2716
MMIC wideband amplifier
8. Application information
Figure 1 shows a typical application circuit for the BGA2716 MMIC. The device is internally matched to 50 , and therefore does not need any external matching. The value of the input and output DC blocking capacitors C2 and C3 should not be more than 100 pF for applications above 100 MHz. However, when the device is operated below 100 MHz, the capacitor value should be increased. The nominal value of the RF choke L1 is 100 nH. At the frequencies below 100 MHz this value should be increased. At frequencies above 1 GHz, a lower value can be used to tune the output return loss. For optimal results, a good quality chip inductor or a wire-wound SMD type should be chosen. Both the RF choke and the 22 nF supply decoupling capacitor C1 should be located as close as possible to the MMIC. The printed-circuit board (PCB) top ground plane, connected to pins 2, 4 and 5 must be as close as possible to the MMIC, and ideally directly beneath it. When using via holes, use multiple via holes, located as close as possible to the MMIC.
VS
C1
VS
C2
L1 C3
RF input
RF_IN
RF_OUT
RF output
GND1
GND2
mgu436
Fig 1. Typical application circuit.
Figure 2 shows the PCB layout, used for the standard demonstration board.
9397 750 13292
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
4 of 14
Philips Semiconductors
BGA2716
MMIC wideband amplifier
30 mm
PH
30 mm
PHILIPS
IN
OUT
V+
PH
DUT C2 C3
PHILIPS
IN
L1 C1
OUT
V+
001aab256
Material = FR4; thickness = 0.6 mm, r = 4.6.
Fig 2. PCB layout and demonstration board showing components.
8.1 Application examples
The excellent wideband characteristics of the MMIC make it an ideal building block in IF amplifier such as LNBs (see Figure 3).
9397 750 13292
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
5 of 14
Philips Semiconductors
BGA2716
MMIC wideband amplifier
As second amplifier after an LNA, the MMIC offers an easy matching, low noise solution (see Figure 4). As driver amplifier in the TX path, the good linear performance and matched input/output offer quick design solutions (see Figure 5).
mixer from RF circuit wideband amplifier oscillator
mgu438
to IF circuit or demodulator
Fig 3. Application as IF amplifier.
mixer antenna LNA wideband amplifier oscillator
mgu439
to IF circuit or demodulator
Fig 4. Application as RF amplifier.
mixer from modulation or IF circuit wideband amplifier oscillator
mgu440
to power amplifier
Fig 5. Application as driver amplifier.
9397 750 13292
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
6 of 14
Philips Semiconductors
BGA2716
MMIC wideband amplifier
90 +1 135 +0.5 +2 45 1.0 0.8 0.6 +0.2 100 MHz 0 0.2 0.5 1 4 GHz 2 5 10 0.4 0.2 0 0
+5
180
-0.2
-5
-135
-0.5 -1 -90
-2
-45 1.0
001aab257
IS = 15.9 mA; VS = 5 V; PD = -35 dBm; Zo = 50 .
Fig 6. Input reflection coefficient (s11); typical values.
90 +1 135 +0.5 +2 45 1.0 0.8 0.6 100 MHz +0.2 +5 0.4 0.2 180 0 0.2 0.5 4 GHz 1 2 5 10 0 0
-0.2
-5
-135
-0.5 -1 -90
-2
-45 1.0
001aab258
IS = 15.9 mA; VS = 5 V; PD = -35 dBm; Zo = 50 .
Fig 7. Output reflection coefficient (s22); typical values.
9397 750 13292
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
7 of 14
Philips Semiconductors
BGA2716
MMIC wideband amplifier
0 |s12 | 2 (dB) -20
001aab259
30 |s21| 2 (dB)
001aab260
(2)
20
(1)
(3)
-40
10
-60 0 1000 2000 3000 f (MHz) 4000
0 0 1000 2000 3000 f (MHz) 4000
IS = 15.9 mA; VS = 5 V; PD = -35 dBm; Zo = 50 .
PD = -35 dBm; Zo = 50 . (1) IS = 19.5 mA; VS = 5.5 V. (2) IS = 15.9 mA; VS = 5 V. (3) IS = 12.4 mA; VS = 4.5 V.
Fig 8. Isolation typical values.
20 PL (dBm) 10
(s122)
as a function of frequency;
Fig 9. Insertion gain (s212) as a function of frequency; typical values.
20 PL (dBm) 10
(1) (2) (3)
001aab261
001aab262
(1) (2) (3)
0
0
-10
-10
-20 -40
-30
-20
-10 PD (dBm)
0
-20 -40
-30
-20
-10 PD (dBm)
0
f = 1 GHz; Zo = 50 . (1) VS = 5.5 V. (2) VS = 5 V. (3) VS = 4.5 V.
f = 2.2 GHz; Zo = 50 . (1) VS = 5.5 V. (2) VS = 5 V. (3) VS = 4.5 V.
Fig 10. Load power as a function of drive power at 1 GHz; typical values.
Fig 11. Load power as a function of drive power at 2.2 GHz; typical values.
9397 750 13292
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
8 of 14
Philips Semiconductors
BGA2716
MMIC wideband amplifier
8 NF (dB) 7
001aab263
5 K 4
001aab264
3 6
(1) (2)
2
5
(3)
1
4 0 500 1000 1500 2000 2500 f (MHz)
0 0 1000 2000 3000 f (MHz) 4000
Zo = 50 . (1) IS = 19.5 mA; VS = 5.5 V. (2) IS = 15.9 mA; VS = 5 V. (3) IS = 12.4 mA; VS = 4.5 V.
IS = 15.9 mA; VS = 5 V; Zo = 50 .
Fig 12. Noise figure as a function of frequency; typical values.
Fig 13. Stability factor as a function of frequency; typical values.
9397 750 13292
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
9 of 14
Philips Semiconductors
BGA2716
MMIC wideband amplifier
Table 8: Scattering parameters VS = 5 V; IS = 15.9 mA; PD = -35 dBm; Zo = 50 ; Tamb = 25 C. f (MHz) s11 Magnitude Angle (ratio) (deg) 100 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 3200 3400 3600 3800 4000 0.182562 0.123465 0.107855 0.114731 0.130176 0.144984 0.160922 0.179351 0.20199 0.218268 0.233965 0.242904 0.246576 0.249069 0.243665 0.233266 0.222055 0.207486 0.191654 0.175783 0.163768 102.7794 87.55274 58.58513 40.14071 24.28555 9.657616 -7.518892 -23.35989 -41.01349 -60.71294 -81.48254 -103.1109 -125.52 -148.8707 -172.646 163.9035 140.7754 117.0531 94.64431 71.9551 49.89436 s21 Magnitude Angle (ratio) (deg) 12.69581 13.13419 13.47149 13.57901 13.67457 13.91705 14.10949 14.2808 14.3825 14.26935 14.0667 13.83968 13.46447 12.74638 11.87558 10.94049 10.05626 9.576357 9.199166 8.912598 8.618058 13.48682 -5.272917 -31.7377 -53.09631 -73.60665 -94.01973 -114.55 -135.3117 -156.7041 -178.3843 160.1504 138.2379 115.7594 93.38644 71.02792 50.42722 30.75908 11.98315 -7.677643 -27.73098 -48.90874 s12 Magnitude Angle (ratio) (deg) 0.029472 0.035438 0.035299 0.033167 0.033194 0.029047 0.028188 0.025188 0.022257 0.019611 0.018087 0.017203 0.016318 0.015514 0.014954 0.015522 0.016261 0.016664 0.016982 0.017094 0.017414 28.74955 -2.202361 -22.54301 -43.06353 -59.63503 -76.09972 -88.34045 -101.2729 -110.3342 -121.0192 -127.6765 -137.8213 -138.8717 -147.6622 -152.1988 -163.8718 -170.5637 -176.5407 176.9385 165.8227 157.6095 s22 Magnitude Angle (ratio) (deg) 0.39239 0.267851 0.227252 0.227993 0.234967 0.239818 0.242141 0.243087 0.24499 0.255598 0.269829 0.283613 0.29058 0.281505 0.25135 0.211425 0.165534 0.118726 0.083354 0.058549 0.055225 91.48628 62.37296 24.6455 -3.493572 -31.11084 -60.54722 -91.56898 -124.5484 -158.6224 167.5983 136.117 106.0987 77.95189 50.68612 24.40624 -0.674037 -23.9944 -46.28101 -72.36691 -109.9804 -163.7132 1.3 1.2 1.2 1.3 1.3 1.4 1.4 1.4 1.5 1.7 1.8 1.9 2.0 2.2 2.5 2.7 2.9 3.0 3.2 3.3 3.3 K-factor
9397 750 13292
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
10 of 14
Philips Semiconductors
BGA2716
MMIC wideband amplifier
9. Package outline
Plastic surface mounted package; 6 leads SOT363
D
B
E
A
X
y
HE
vMA
6
5
4
Q
pin 1 index
A
A1
1
e1 e
2
bp
3
wM B detail X Lp
c
0
1 scale
2 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A 1.1 0.8 A1 max 0.1 bp 0.30 0.20 c 0.25 0.10 D 2.2 1.8 E 1.35 1.15 e 1.3 e1 0.65 HE 2.2 2.0 Lp 0.45 0.15 Q 0.25 0.15 v 0.2 w 0.2 y 0.1
OUTLINE VERSION SOT363
REFERENCES IEC JEDEC EIAJ SC-88
EUROPEAN PROJECTION
ISSUE DATE 97-02-28
Fig 14. Package outline; SOT363 (SC-88).
9397 750 13292 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
11 of 14
Philips Semiconductors
BGA2716
MMIC wideband amplifier
10. Revision history
Table 9: Revision history Release date 20040924 Data sheet status Product data sheet Change notice Doc. number 9397 750 13292 Supersedes BGA2716_N_1 Document ID BGA2716_2 Modifications: BGA2716_N_1
*
The format of this data sheet has been redesigned to comply with the new presentation and information standard of Philips Semiconductors Preliminary data sheet 9397 750 12827 -
20040202
9397 750 13292
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
12 of 14
Philips Semiconductors
BGA2716
MMIC wideband amplifier
11. Data sheet status
Level I II Data sheet status [1] Objective data Preliminary data Product status [2] [3] Development Qualification Definition This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN).
III
Product data
Production
[1] [2] [3]
Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
12. Definitions
Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
13. Disclaimers
Life support -- These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
14. Contact information
For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com
9397 750 13292
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
13 of 14
Philips Semiconductors
BGA2716
MMIC wideband amplifier
15. Contents
1 1.1 1.2 1.3 1.4 2 3 4 5 6 7 8 8.1 9 10 11 12 13 14 Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General description. . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data. . . . . . . . . . . . . . . . . . . . . 1 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 2 Thermal characteristics. . . . . . . . . . . . . . . . . . . 3 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Application information. . . . . . . . . . . . . . . . . . . 4 Application examples . . . . . . . . . . . . . . . . . . . . 5 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 12 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 13 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Contact information . . . . . . . . . . . . . . . . . . . . 13
(c) Koninklijke Philips Electronics N.V. 2004
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 24 September 2004 Document number: 9397 750 13292
Published in The Netherlands

▲Up To Search▲

Price & Availability of BGA2716

	To Download BGA2716 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .